Learn Welding and the Process of MIG Welding

This process is called by many names and it basically is a welding process that uses an arc to heat metal that needs to be joined. The welder uses a continuous feed filler metal (a consumable) electrode and this is used on the work-piece. This type of welding also must use a shielding that is provided by a gas or a mixture of gasses.

This type of welding is also called short circuit transfer. In the MIG process, when the wire actually touches the metal to be connected, it lets go of the metal that does the welding. This makes sure that metal doesn't transfer across an arc so there is no puddling.

Also known as Welding , the MIG(GMAW) process uses a metal gun to provide this service instead of a torch so that you get a direct current going to the metal. You can use both constant current and alternating current systems to also produce this method of welding.

Welding uses four ways to transfer metal. These are:

Globular -- this method is difficult and used the least because it has a tendency to spatter because the gun will move to a high heat without warning. There will be flaws on the welding surface if this happens.  This method uses carbon dioxide so the electrode tends to produce a ball of melted metal that cases irregular shapes that are bigger than the electrode. They then drop and falls onto the piece you are working on which causes a spatter. This is difficult to control as you would imagine.

Short circuiting -- this uses a smaller current than the globular method but it still uses carbon dioxide. Because of the lower current you can actually weld thinner metals together with this method. This method is similar to the globular method because drops of melted metal from the electrode still forms, but it causes the electrode to short circuit instead of the drops falling on the work. This closes off the arc but comes back again because the surface tension pulls the metal goblet from the tip.

Spray -- this was the first method for transfer used with Welding and used to weld aluminium and stainless steel. The difference with this process is that the electrode metal passes through an electric arc that is stable and goes all the way to the workplace. What this will do is stop the various spatters which helps you get a weld finish that is a very high quality. You also will watch as the current and voltage increases so you get small, vaporized steam droplets instead of large globules.

Pulse spray -- this last one is a newer way of doing this type of welding that uses a continuous current that pulses and melts the filler wire. In each pulse a small droplet of metal will fall.

This also allows the welder to use a lower current. The welder gets a more stable arc and this stops spatter and the short circuiting process. Because this process is slower, argon gas is used instead of carbon dioxide as the shielding gas.

Welder World is a brand new community website for weldering to connect with one another and gather free information on welding. Come by WelderWorld to get your free Ebook on Welding Basics just for joining the Welding community for free. You will find Welding Forums, Welding Blogs, Welding Community Members and more just for signing up for free to join and then you can get your free Welding EBook on Welding Basics. Come be A part of our Welding Community.

Learn about TIG Welding Basics and Tips

TSince TIG(GTAW) welding can be difficult there is all kinds of information that will help you understand it better and how to do it more effectively. Just like with any other method, you want certain things prepared before you begin, and its the same with TIG Welding.

What to prepare
The first thing you want to do is prepare the area where you are going to do your welding because you want it to be kept free of contamination. This means that you will have to really clean the area to make sure you have no grease, moisture or dust. You will also want to make sure there are no air drafts in this area because this could bring more problems.

The next thing to prepare is the metal that you are going to use for Welder . You want to start with your surface and your joints as clean as possible and the best tool to do this is by using a stainless steel wire brush.  Many welders will dedicate one brush to whatever metal they have so they don't have to worry about cross contamination.

If have slag on any of the metal you can remove it with a file. Next, you will want to clean the base metal. The reason you want everything to be so clean is that if contaminated, the metal can either break down or make a bad connection. Of course, it depends on the metal which it will do, so cleaning everything can stop this from happening.

Beginning to weld
Its very important to have a shield gar because this shield gar will help so things don't come in and contaminate your weld. Most welders will use Argon because it seems to work best with Welding . By using this gas, you are protecting the area from oxygen which can contaminate what you are doing.

If you are using thicker aluminum, you can also add helium to the Argon because it ionizes hotter than Argon and you will need the hotter temperature in these types of welds. If you need helium you can get these already premixed, this is available with your gas supplier.

A note about suppliers: they are not the same so you will want to make sure you use someone who is reputable. You will also want to make sure you have all the seals checked for leaks before you buy.

When you are checking for Welding leaks as you weld the best way is to use water and soap and a small acid type brush. These together will produce bubbles if there are any gas leaks. All you do is apply this solution of water and soap on the joint to and if you see air bubbles, you know you have a leak.

You will want to check all your supply hoses and gas connections to make sure there are no leaks before you get started. Make sure the torch insulators and your o-rights are fitting properly and that the seals are intact.

If you are like a lot of people and like to avoid problems before they start, the best thing to use is a gas lens on your torch so you can see easier.

Welder World is a brand new community website for weldering to connect with one another and gather free information on welding. Come by WelderWorld to get your free Ebook on Welding Basics just for joining the Welding community for free. You will find Welding Forums, Welding Blogs, Welding Community Members and more just for signing up for free to join and then you can get your free Welding EBook on Welding Basics. Come be A part of our Welding Community.

Welding Terminology

If you are interesting in Learn Welding there are many different terms that you will want to familiarize yourself with in order to read magazines or books on the topic. Here is a list of common terms that are important to know in Welder : 

ACETYLENE -- this is a gas that you will be working with to do Learn Welding . It is a very flammable gas so you have to be careful with it. This gas is made up of carbon and hydrogen and it is used in the oxyacetylene type of welding process.

AIR-ACETYLENE -- this is a flare that you can produce using low temperature. It is created when you burn acetylene with air and not oxygen.

AIR- CARBOM ARC CUTTING (CAC-A) -- Using the heat of a carbon arc - this is how you do this type of arc cutting.

ALLOY -- this is a mix that has metallic properties because it has at least one element that is metal, but it can have several other things in the mix as long as one is metal.

ALTERNATING CURRENT -- a current that goes backward and forward at regular intervals (see DC Current).

BACK FIRE -- this is the popping sound that you hear when you turn on the acetylene torch when you connect it with fire. It is created because the flame turns back into the tip for a moment and then comes back out of the torch as a flame.

Backhand Welding -- This is the pointing of the flame at the weld that is already complete.

BACKING STRIP -- this is a strip of material that you will use when you need to keep metal that is melted at the bottom of the weld. You may also use this strip to add strength to the thermal load of a joint so you can stop the base of the metal from warping too much.

BASE METAL -- this is what you call the metal that you are going to weld or that you are going to cut. If this is an alloy, it will be the metal that you have in the highest amount.

BRAZING -- this is actually several welding processes. You will use this when you have a groove, fillet, lap or flange joint that you need to bond. This will require a nonferrous filler metal that has a melting point higher than 800 degrees F (427 degrees C) but less then your base metals.  Then, the filler metal will be distributed throughout the joint using capillary attraction.

DIRECT CURRENT (DC) -- a current that only flows in one direction -- forward.
- Flows in one direction and does not reverse its direction of flow.

DEFECT -- there can be defects in your weld after you create it. The main defects you can find are things like cracks, porosity, places where the metal has been undercut, or where you have a slag inclusion.

EDGE JOINT -- this is where you set two plates and put them together at a 90 degree angle with their outer edges.

Welder World is a brand new community website for weldering to connect with one another and gather free information on welding. Come by WelderWorld to get your free Ebook on Welding Basics just for joining the Welding community for free. You will find Welding Forums, Welding Blogs, Welding Community Members and more just for signing up for free to join and then you can get your free Welding EBook on Welding Basics. Come be A part of our Welding Community.

Learn Welding and the Process of TIG Welding

The acronym TIG stands for Tungsten Inert Gas Arc Welding and the acronym GTAW stands for Gas Tungsten Arc Welding this is the same process but it is referred to by these two different names.

In the situation you will be Welder using an electric arc that generates the heat. You then have a tungsten non-consumable electrode that then produces the weld you are attempting to make.

One of the things that have to happen in this type of welding is that the particular metal that you are welding has to be shielded from contamination in the atmosphere or you will get a poor weld. Hence, the area is blocked with inert gass and sometimes used with a filler metal where it is deemed necessary.

This type of welding needs constant current to flow across the arc using an ionized gas called plasma. Plasma also has metal vapours within it. You will usually use GTAW if you have to weld thin metals like stainless steel, aluminium, magnesium or copper allows. GTAW also gives the person who is operating the welding process more control of the weld.

What this means to the weld is that it is a stronger weld and has a higher quality than many other types of Welder . Many experts say that it is harder to learn, is complex and can be slower than other welding techniques.

Some welders like using a different kind of torch to produce plasma arc welding which is very much like this one but a little different. This type of welding will give a more focused welding arc, but usually this is done through automation.

How It Operates
The reason this welding process is the most complicated or difficult to master is because the welder has to use a smaller arc length; they have to be able to have a very steady hand. If they aren't able to keep a distance between the electrode and the piece they are working on, the piece can become contaminated and there can be problems with the weld.

This is also a two handed process because you have to be able to hold the torch in one hand and feed a filler metal into the space that you are welding. You can see that this is a very intricate process and one that requires high skill.

There are a few types of Welding that will not require this type of weld and the individual will not have to use filler material these types include: edge, corner and butt joints. These types of welds are called autogenous or fusion welds (Source: Wikipedia).

A welder who is highly skilled in this process is able to alternate between using the torch and then using the filler material in a pretty fast way.  As they do this the filler rod can be taken out as the electrode moves forward, and it doesn't have to be taken out of the gas shied. For those who are trained and can perform the process well, this is a highly developed process.

GTAW can operate using several different currents: positive direct current, negative direct current or alternating current. This will all depend on how they set up the power supply in the beginning.

Welder World is a brand new community website for weldering to connect with one another and gather free information on welding. Come by WelderWorld to get your free Ebook on Welding Basics just for joining the Welding community for free. You will Find lots of benefits to this welding community such as forums, blogs, and other community members plus you can get the free basic ebook on welding just for stopping by. Visit and become one of our Welding Community Members.

Learn the Types of Welding

When you think about Welder you might think that there is only one type of welding. This is a common idea because most people only see the finished product. However, there are many different types of welding that you might find interesting.

Welding is basically taking to metals and getting a tight bond between them by welding them together. There are a variety of bonds that are done depending on the types of welding you use.

Types of welding fit under categories as listed here:

Gas welding
This type of Learn Welding creates a flame from a burning gas and this creates the welding heat that is needed. You will see this in the following types of welding:

Propane torches -- people use this when they want to sweat a joint or when they want to solder two pieces of metal together. This is one of the lowest heats and can be used for small things.

Oxyacetylene torch-- this heat gets a bit hotter and many people say this is the most universal type of welding tool you can find. This is used when you need a very hot flame. This type of torch will weld a variety of things as long as you have the right metals and tools for it. It is generally used when you want to cut, braze, weld or solder something that requires a higher heat. You have to be careful though because it is a type of heat that can be difficult to control and it can sometimes overheat the area.

Oxy-propane -- this type of welding is used when you want to solder, braze or heat something. This is a cheaper form of both of the types of welding that was first listed.

Arc welding
This type of welding creates the heat through the use of an electric arc. The types of welding that are done through this type of welding include:

Basic AC & DC arc welders -- when you are looking for a way to weld either heavy gauge steel or cast iron this is the type of welding to use. It uses rods that you guide along the place to be weld and these are made of flux coated steel or other materials.

MIG (Metal Inert Gas) -- this is a very quick way of Welding and some say it is easier to do than regular arch welding. It is done through the use of a DC arc and it uses filler metal that is used with a spool of thin wire. You use inert gas instead of flux. This is usually used with steal bodywork and is a good choice when you need to weld sheet metal.

TIG -- How this works is that there is an AC arc that is of very high frequency and then its combined with a tungsten electrode that is shielded by inert gas. This comes together to create a torch that is controllable. This is a good choice to weld very thin metals together. If you are trying to work with alloys such as stainless steel and aluminum then you are going to want to pick this as your choice.

Welder World is a brand new community website for weldering to connect with one another and gather free information on welding. Come by WelderWorld to get your free Ebook on Welding Basics just for joining the Welding community for free. You will Find lots of benefits to this welding community such as forums, blogs, and other community members plus you can get the free basic ebook on welding just for stopping by. Come be A part of our Welding Community.

Find out about the History of Welding

When you drive your car or look at a light fixture in the street or open your microwave, chances are that there is something in any of those items that has been welded. These products and others have been a part of the process of Welder for more years than you might imagine.

Welding actually started a very long time ago during the Middle Ages. Many artifacts have been found that date back to the Bronze Age. These have been small boxes that were welded together with what is called lap joints; no one is exactly sure what these were used for, but this was important to that time.

The Egyptians also made a variety of tools by welding pieces of iron together. Perhaps this is where Maxwell's Hammer comes later? Who can say! Next you will find that in the Middle Ages those people would always use blacksmithing for Iron. Different modifications were made along the way until the welding that is used to day was developed.

There were several significant inventions in the 1800s that influenced welding included here:

§ The invention of acetylene by an Englishman named Edmund Davy.
§ Gas welding and cutting became known and a way to cement pieces of iron together.
After the invention of the electric generator, Arc Lighting was one of the most popular parts of welding.
§ Arc and resistance welding become another popular aspect of welding.
§ Nikolai N. Benardos receives a patent for welding in 1885 and 1887 from America and Britain.
§ C.L. Coffin receives an American patent for a arc welding process.

After the 1800s many more patents and inventions were made in order to create more ways of doing welding but one of the greatest needs would come much later during World War I because this process was needed to create arms. Because of the demand Welder firms became a staple of America and Europe because the war needed welding machines and electrodes to go with them.

During the war people really got a chance to look at how welding worked and it became a very popular way of work. The very first American Welding Society began in 1919. This nonprofit organization came directly out of through a group of men who called themselves  the Wartime Welding Committee of the Emergency Fleet Corporation (Source: Miller Welds).

The 1950s and 1960s were also a significant time for welding because a Welder process using CO2 was discovered and a variation of this form of welding that used inert gas became very popular in the 1960s because it produced a different type of arc.

There have been a number of improvements in the welding trade over these years and today the process has added two areas, friction and laser welding. These two have created a more specialized field and therefore more opportunities for learning.

One interesting point about laser welding is that those people who use it have found that is a tremendous heat source so it can actually weld both metal and non-metal objects.

Welder World is a brand new community website for weldering to connect with one another and gather free information on welding. Come by WelderWorld to get your free Ebook on Welding Basics just for joining the Welding community for free. You will find Welding Forums, Welding Blogs, Welding Community Members and more just for signing up for free to join and then you can get your free Welding EBook on Welding Basics. Come be A part of our Welding Community.

 

What is Welding and How does it work?

Wikipedia defines Welding as “a fabrication process that joins materials, usually metals.” This is done by melting the part of the materials to be joined and adding some additional molten joining material. When the molten material cools, it forms a strong bond or joint.

Welding is the most widely practiced way of joining metals together due to the efficiency and economy of the process. It has been estimated that approximately 50% of the Gross National Product of the USA arises from activities that are in some for or another related, perhaps remotely, to Welding . As an example, farming may appear to have nothing to do with welding, but the equipment the framer uses to grow and harvest his crops will have used welding in their manufacturing process.

Until the advent of the 20th century, welding was confined to blacksmith shops where two pieces of metal were heated to very high temperatures in a forge and then hammered together until the joining occurred. This is what is called forge welding.

There was a point at which welding became much more easy and cost effective and that point was when we introduced electricity into the industrial world. Today there are 4 types of welding techniques that are commonly used.

· The most basic for is Arc Learn Welding where the parts to be joined together are brought into contact with strong electrical current and heated. The molten parts are then joined together to form a weld. Most would agree that this is the cheapest and least sophisticated form of welding.
· Gas Welding is generally used for repair work especially in the case hollow items like tubes and pipes. Hot gas is forced onto the surfaces to be welded. This procedure requires the parts to be subjected to less heat and is suitable for material that may be damaged by exposure to high temperature. For this reason it is used in the jewellery industry which has to work with soft metal with low melting points.
· Resistance Welding requires that an additional sheet of material is used to cover the pieces that are to be welded together. This provides great strength to a weld, but the process requires expensive equipment and also the use of additional material to encase the weld which makes it expensive and not suitable for all applications.
· Laser Welding is the most modern technology available. High intensity lasers can be tightly focused and produce controllable heat on the surfaces to be welded very quickly. This is perfect for material which can be damaged by prolonged exposure to extreme heat. Laser welding is very accurate and can be used to produce even the smallest of welds. However, because of the high capital cost involved in purchasing this equipment, the cost of welding is also high.

Although the perception of welding is that of a simple process of heating and joining, it is a high technology industry with huge amounts being spent of research and development to find stronger, more accurate and cheaper methods. The welding process plays a big role in metallurgy with a constant effort underway to find newer and more weld friendly alloys.

Welder World is a brand new community website for weldering to connect with one another and gather free information on welding. Come by WelderWorld to get your free Ebook on Welding Basics just for joining the Welding community for free. If you stop by Welder World you will see some of the things the community has to offer such as Welding Forums, Welding Blogs, and other Welding Community Members plus you can still get your free Ebook on Welding. Come be A part of our Welding Community.

Vauxhall Corsa - Vauxhall's Small Success Story By Jon Barlow

Vauxhall’s little Corsa started life way back in 1983. Back then it was known as the Nova in the UK and was a replacement for the ageing Vauxhall Chevette. I remember the Chevette well as my friend’s Mum owned one and we persuaded her to let us borrow it the day after my friend passed his driving test on the fourth attempt (you could tell he was a natural behind the wheel). The car was a pretty revolting shade of purple and showed a few battle scars as my friend’s Mum wasn’t exactly an expert driver either. We didn’t care though as it was the perfect opportunity to tear up the L-plates that had adorned the car for what felt like an eternity. We were then ready to hit the streets with our puny cassette radio blaring. What we did manage to hit within about ten minutes was a car full of rather large Rastafarian gentlemen who were none too pleased with the damage that we had caused to their bright orange Fiat Super Mirafiori. It took a considerable amount of diplomacy to resolve the situation but luckily we managed to escape with our dignity, and our front teeth intact. A few years later I got a job with a company that had a Vauxhall Nova “Club” as a pool car and I must admit I did not enjoy driving that thing around at all. It was not actually so bad to drive but the car was white with yellow trim and had a yellow and white checked interior that made you feel like you were driving a deck chair. This was finished off with some tasteful white windscreen wipers. It was truly hideous and I was glad the day when somebody stole it and set it on fire which was a very popular past time back in the late eighties. I’m not sure who left the keys in it making it easier to steal though. I’m sure it couldn’t have been me. Vauxhall dropped the Nova name in 1993 and adopted the Corsa title as everyone was getting confused, as indeed they always have been between Vauxhall and Opel names over the years. The more rounder Corsa B model was quite a departure from the previous squarer Nova but proved to be just as popular although the A model British Nova still has a loyal following although they are becoming rare these days. Another model which appeared was the Tigra and although based around the Corsa B did not sell terribly well. The new millennium heralded the appearance of the Corsa C model which was a more technologically advanced version of what had gone before. GM engineers dubbed the chassis "Gamma" which was developed to be a design platform for other models as well.This process was also used by other manufacturers. “Ecotec” engines were carried over from the previous model due to their proven reliability although a few alterations were made in particular to the old DI diesel engine which made way for the improved CDTI version. The Corsa C was a huge success in the UK consistently selling in large numbers and achieved best selling car status as well as best sales in its class of “Supermini” throughout the early part of the decade. As a result of this success Vauxhall even resurrected the Tigra again in 2004 although it is now known as the “Twin Top”. 2006 saw the arrival of the Corsa D which has a new Gamma platform that was co-developed with Fiat and also features on the Grande Punto. The latest Corsa looks and feels like a bigger car and is more refined than its predecessors. Sales have been good to date with the Corsa still ranking in the top five of best selling small cars. A clever option on the Corsa is the “Flexfix” integrated bike rack which can be pulled out from the car’s rear bumper and incorporates the number plate together with the lights; which are often obscured by traditional bike carriers.

The Problem With Gas Mileage Improvement Is?

Now that gas is almost three dollars or more a gallon, people will do anything to see some gas mileage improvement when they drive long ways from home. However, it is starting to hurt just driving back and forth to work as well. When gas prices go up, people stay home more and that means a loss for the travel industry and hotels. Along the same lines, people have to pay more for services that rely on gas like air travel and bus travel. Until the prices go down, if they ever do, you have to do a few things to save money.

The problem with gas mileage improvement is that there is not much you can do to save money other than stay home or carpool. You can keep your engine in top shape, and make sure all filters are clean and clear, but the difference is not going to add up to much. Some suggest that turning off the air conditioning and rolling down the windows will help with gas mileage improvement, but some think that having the windows down creates more resistance to the wind, and that means more gas is needed to travel at the same speed as usual.

You might want to skip the small things you can do to see gas mileage improvement, and go for the larger things that will show and immediate affect in your wallet. This means that you have to find a new way to get to work. You should find someone to ride to work with, and you can take turns driving and/or paying for gas. If you can get more than two people in on the deal, you are going to save more money. You could also ride a bike to work, but that is not always possible or reasonable for everyone.

Some are saying that gas prices are not high enough to effect true gas mileage improvement. They say that prices must get higher in order for people to make real changes and to become less reliant on gas. I can see the logic behind this, but I don’t think that is something that is fair for most people. When the gas prices go up, people begin to stay home more and that means a loss for the travel and hotel industry . It would only serve to hurt those who are not wealthy and destroy the economy.

Best Gas Mileage SUV

SUV fuel economy is not exactly legendary. A matter of fact, SUVs are known far and wide as some of the biggest gas guzzlers that are.  So when one of my friends announced that he was looking for the best gas mileage SUV rating, I was a little bit surprised. It didn't really make any sense. If you're going to buy an SUV, you giving the world a certain message: luxury matters to me much more than efficiency. Of course there are certain SUV companies such as Subaru which specifically market to hippies and other supposedly environmentally conscious folks, but even these are not known for being tremendously energy-efficient. Still, I was intrigued. I wanted to find out more about the best gas mileage SUVs.

The real problem is that the category SUV is pretty flexible. Although they are supposed to be rugged vehicles equipped for off-road driving, the reality is much different. Many of them are simply status symbols for people who like to show off. They are roomy inside, high above the ground, and big enough so that if they get in crashes, the other car takes the worst of it. That isn't to say that SUVs are safe. Even the best gas mileage SUV won't save you from a rollover crash, and that can be fatal. Nowadays, many of the design flaws inherent in sport utility vehicles are being corrected, but I still wouldn't trust one with my life without doing a lot of research.

The biggest problem with this project, of course, was coming up with a definition for what an SUV is. A car like the Saturn Outlook, for example, might be considered an SUV but might not. Would a crossover car qualify for the best gas mileage SUV? It is pretty hard to tell, and my friend couldn't decide.

In a lot of ways his whole project was a waste of time. It did have one good effect, however. Researching the best gas mileage SUV really got him thinking. For the amount of money that he could spend buying a new SUV, he could get something that was really fuel-efficient such as a Honda hybrid car. He came to realize that he didn't really need an SUV. He didn't have much to carry around, and he didn't go off-road very often. Instead, he invested his money in a fuel-efficient car. It might not be as big and overbearing, but it is a better investment in the long term.

How To Save Gas Mileage Without Any Fuss

In today’s world, the skyrocketing prices of gasoline makes a huge dent in your expenditures, and we are always looking for ways to improve this situation.

Who wants to continue spending large amounts of their hard-earned money on gasoline? 

Nobody of course!

Wouldn’t it be excellent if you knew some tricks to help improve your current gas mileage so you can save more of your hard earned money?

In order to do this, you just need to keep in mind these simple solutions, realise their importance, and utilise them in your daily routine.

Here is a list of some of these important points:

Change the way you drive: this is the easiest way to save a lot of money as you don’t need to spend anything to make this method work; all that is required is to bring a few changes in you and see it showing wonderful results.

You must learn to slow down on freeways. You should not drive at high speed especially
when you are going on a short journey. Make an effort to maintain your speed and keep the use of brakes to a minimum.

Drive when it is cooler outside: driving at such a time will reduce the stress on the vehicle and that will help you improve fuel economy.

Coasting to stop signs and lights: if you drive fast and stop right at the last moment, you are using more gas than what is actually required. It is always better to coast up to a light or stop signal. You should use this trick to coast downhill also, whenever possible.

Use the traffic to your advantage: when you are driving at high speeds, it is better to drive behind a big vehicle like a truck. Don’t forget to keep a safe distance in doing so. When you drive like this, you reduce the wind resistance and this can save on gas mileage by 5% to 10%.

Take proper care of your vehicle: your vehicle should be properly maintained if you want good results in mileage improvements. Check that the air filter is not dirty and make sure that the tyres are properly inflated. Even doing these little things will make a massive difference.

Get timely oil change and tune ups done: they are a must for the improvement in mileage of your vehicle. You must get it done every 3,000- 4,000 miles.

Use water to run your vehicle: yes it is possible to do so! Water is a cheaper and better alternative to expensive gasoline. HHO generators are installed in the vehicles that use water. It helps to save your hard earned money and is also beneficial in fighting global warming. The HHO gas extracted from water reverts back to its original state when it exits your vehicle. This method causes zero pollution and is affordable too.

You can follow any of these methods and enjoy the benefits of improved gas mileage.

The added advantage is that any of these solutions are successful in all vehicles, whether it is a car, truck, SUV or anything else.

How To Run Your Car On Water Kits Scams

run your car with water

Run your car on water. Doesn’t it sound too good to be true?

But it’s a fact that today this technology has seen a lot of improvement and has contributed to the invention of HHO generators that allows your car to run on water. These generators are not only used to make your vehicle move but they are also a significant factor in helping to lower the cost of operating your vehicle.

Let us first try to understand the principle on which this idea is based. We know that water is made of hydrogen and oxygen. The HHO or the Hybrid Hydrogen Oxygen generators work on the technology of using this hydrogen and oxygen.

The electricity from the battery of the car is obtained and then it is burned to produce a gas that is known as HHO. This gas creates the energy required to cause motion in a vehicle through combustion.

It follows a simple concept; to remove the hydrogen from the water, which leaves the oxygen behind, oxygen that is required for combustion, thus making it possible to generate energy that would drive a vehicle.

This idea is not a new one. It was actually developed many years ago but was not given much importance then. Nowadays, with the increase in fuel prices, this idea has gained more popularity. Though some still don’t believe that it is possible to use water as an alternate fuel, there are many who have been using it for some time now and are more than happy with the results.

This technology is relatively cheap, affordable and contributes significantly to the accelerated mileage of a motor vehicle.

When you think about making an effectively operational HHO generator, it sounds like a complex task. You feel that technicians and experts with experience only, can do it. But the fact is that it is not as difficult as it sounds.

It is better to learn how to build a HHO generator rather than going for the ready made ones. The ready made generators are not only hard to find but even if they are found, you will pay a huge amount for them.

Then, as well as, spending an exorbitant amount on it, you will also need professional help to get it installed. That means spending more and more money. Thus it is advisable to build an engine on your own and install it too.

But before doing that, you should consult the various well reputed hydrogen conversion guides that are posted on the Internet. The entire process is explained in an easy to understand, step-by-step approach. You can even get all your doubts cleared from them.

They definitely will help you save a lot of money that you would have otherwise spent on buying a ready made HHO generator and the cost of installation.

This technology is slowly gaining acceptance and popularity, as besides its affordability factor, it is also safe and reliable. The use of a HHO generator also increases gas mileage of the vehicle considerably, depending on the type and make of the vehicle.

It also causes less pollution when compared to other fuels.

You have to try it to believe it!

Find Used Cars Online

Need to buy a used auto online, but are unsure of how to get started? The Internet is a big place, and has numerous resources for used car buyers, but you need to know where to look to find the best deals.

Firstly, it is easy to find used car listing on the website for your hometown paper. These are nice, because they are all typically sellers in your local area which makes it easy to stop by and take a test drive, which is critical for getting the best possible deal on a used car.

Stepping out a little more, you can check online classifieds sites, such as Craigslist, which will expose you to a broad range of sellers, many of whom will be near you, though not to quite the same extent as a news paper might. These sites can be gold mines, though, so be sure to give them a look.

If you're looking to broaden your scope further, try sites like eBay Motors, which brings sellers from all over the country into one convenient location. These listings are both auction format and fixed price, so you have multiple buying options. These sellers will be located all over the country, but you can search for listings that are in your area. To make things better, you can also prevent scams by using eBay's basic buyer protection. Definitely worth checking into.

If you're looking at a very specific model of used car, try search on car enthusiast forums. For example, if you want to buy a late '80s Nissan Z car, then visit some Z car forums to find sellers. Buying from these sorts of sellers can be great, because they are often very knowledgeable and passionate about the cars. You will be able to get a really good idea as to the condition of the car if you go with a seller like this.

There are many other places to find used cars online. You can find used car listings on a wide variety of websites. However, the places I've listed above have the highest amount of listings, and are thus the most "bang for your buck" locations for buying a used car online.

As always, be careful when shopping online. Don't throw away your common sense, and make sure that you're getting a good car at a fair price. If you do your research, check multiple sources for pricing, and check the car over thoroughly for buying, you can certainly buy used cars online and get great deals for it.

I Love The Paintless Dent Removal approach

paintless dent removal

Car dents are not something I appreciated by any means. They depreciate from the value of the vehicle, both monetarily and aesthetically. It was no wonder I was a hundred percent freaked out when I saw the most latest dent in my car.  For one thing for sure, car dents—I care how small, can make the car to appear like trash and for another—it is not as if I am rolling in money.

Car dent repair can be costly and I wasn’t very sure that I could afford to get mine repaired, but I wouldn't want to drive in the neighborhood in a dented car either.  Car dents have a way of multiplying. 

I was searching around for a dent repair shop and enquiring about prices when I found Dent Masters.  Browsing through the website I was delighted by two things: 

1) that their dent removal process was explained so thoroughly on their  site and

2) that they got one of their guys come over to my house and repair the dent for me.  Who doesn’t appreciate a business that comes to you instead of having you to go to them? 

Do I even need to say that I hired them?

This is the way the dent removal technique works. Dent Masters employs a technique called Paintless Dent Removal, or PDR. It is a technique by which the dents are repaired without using tools that require the car to be touched up or refinished. The guys at Dent Master use hand instruments to work on the dent until the dent is totally gone.

Paintless dent removal used to be limited to only tiny dents but now it can be fix bigger dents as well as including dents that would normally need some major body work to repair. The PDR specialists can even repair damage that are  caused by hailstones.

The PDR specialist that came to my house was pretty  nice and talked to me the entire way through the process and when he was done with his work (which did not take nearly as long as I thought it would) my car looked like it had never been dented at all! I had feared that there might be some residual damage—a couple of small scratches in the paint from the tools for example, but there was none!

After knowing a a bit more about Dent Masters, I saw that their business has been around for more than thirty  years and it doesn't surprise. When you witness how this technique works, you won’t thinking of taking your car into a body shop ever again. Rather, you’ll think of Dent Masters your first option.

 

Tips When Searching For A Warranty Quote On The Internet

warranty company

Shopping online for extended warranty coverage isn't as easy as shopping for, say, an MP3 player or even the car itself. Generally, when we're looking for consumer goods on the web, we consult a trusted nonprofit publication like Consumer Reports; however, when it comes to extended warranty coverage for autos, Consumer Reports issued a report that they're ALL a lousy deal! It's easy for them to say, but some people aren't that great at saving huge chunks of money or who worry incessantly "What will I do if I have a breakdown?" For these folks, finding a warranty company is critical for peace of mind. Even without Consumer Reports, there are many sites offering a free online warranty quote, in exchange for a little information, of course.

When you're dealing with a warranty company online, there are a few things to look for. Be sure they're BBB approved and that you can find their address or executive names somewhere on the site. Check to see if the warranty company is backed by an insurer or financial backer, which will guarantee that you'll be covered even if the company suddenly goes belly up. You can then cross-check the financial backer with the AM Best website to see how reliable they are. Your State Insurance Commission can also tell you if any complaints have been filed with the company. Your warranty quote should deliver a clear, comprehensive detailing of what you will get for your money. If they can't provide you with the level of detail you need or if they seem vague, then look elsewhere.

Also, before you get a warranty quote, you may have to consider different coverage options. For example, a "breakdown" warranty may cost less up front, but it also may increase the number of repairs you have to pay for yourself, whereas "wear and tear" warranties will cover most major components, including costly gaskets and seals. Secondly, some warranty companies don't cover you if your car has overheated, so again, it's a matter of price vs. protection. Consider whether you want roadside assistance, towing, trip reimbursement and rental car coverage, should your car fail while you're traveling. If you don't plan on selling your car and transferring the warranty, then you may be eligible to save some money that way. Many consumers also want the choice of choosing the repair shops, as opposed to the warranty company choosing where the work will be done. Additionally, some consumers save money by agreeing to pay for repairs upfront and be reimbursed later, rather than having their warranty company pay the mechanic directly. Understand these options before buying your plan so you can avoid having your claim denied later.

One place you can check is WarrantyHeadquarters.com. Here you can get instant, extended warranty quote information by filling out a quick form. Another site that ensures you the highest quality quotes is WarrantyHelper.com, which asks you if you want "wear and tear" coverage, overheating protection and A-rated insurance. You can also go through recommended companies like Warranty Direct or National Warranty Corporation for added information. Just type "warranty quote" into Google and you'll see how many companies come up! The risk of getting junk mail, telemarketer calls or email spam is always there, of course, so you may want to have certain phone lines or email addresses set up for research purposes only.

The Basics of A Hydrogen Gas Saver

As gas prices continue their shocking rise, many individuals are searching for a way to save money on gas.  When you look for advice on how to save on gas you'll more than likely be told to keep your car tuned up and schedule routine maintenance.  These maintenance tips usually include using the right oil grade in your car, checking the air pressure in your tires and changing the spark plugs to improve gas mileage.  These practices can definitely help, but only on a minimal scale.  People are searching for a magic bullet so to speak and many are finding it in a hydrogen gas saver.

The hydrogen gas saver will boost your cars gas mileage and also drop the emissions let out.  These little gas savers, known also as a hydrogen generator gas saver, are a fantastic way to fight high gas prices.  What this generator does is it makes oxygen and hydrogen gas, otherwise known as HHO.  How this works is it utilizes your cars electrical system, some distilled water and a little bit of baking soda.  There are estimates out that say using only one gallon of distilled water can bring about two thousand gallons of fuel for your vehicle.

What most people don't realize is that these great little gas savers can be put together and installed by you.This can be a great bonus by helping you cut the cost on installation fees that would be charged to you by your local mechanic.There are just a select few reports that will inform you on how to put one of these gas savers together yourself.What most don't know is that these guides supply you with detailed instructions and also point you in the direction of where to get the parts you need.  Upon installation of one of these generators, your cars fuel efficiency will rival those of current hybrids.

With the hydrogen gas saver installed on your car, it will also help lower your cars emissions.  This will also help your car run more efficiently thus providing up to seventy percent better gas mileage.Just imagine for a second what a 70% boost in your fuel economy could mean for your wallet?  Just imagine how much money you could save and what other things you can purchase besides fuel.

Listen, we all know that gas prices are not going to go down anytime in the near future, if not ever.  So if your like many and want to save on gas, purchasing a hydrogen gas saver guide may just be what the doctor ordered.  We all know that it is a good idea to keep your car maintained and schedule it for routine maintenance but this will only keep it's efficiency at factory standards.  There is only one way that you can boost the gas mileage and it is done with technology and a little water.

Auto Auction Secrets

Normal 0

By Jim Nettleton

You may be aware that, all over the country, auto auctions are in full swing at all times. What you may not be aware of is that you can easily find incredible bargains at these auctions that will enable you to purchase a vehicle very inexpensively and possibly even resell it for a profit.

The two leading sources of these auto auctions are banks and the government. In the case of the government, you can be dealing with the federal, state or local level. Banks auction repossessed vehicles, frequently for pennies on the dollar. They are not in the vehicle business and want to turn these unwanted possessions into cash as quickly as possible.

Usually, banks will auction vehicles for what is owed to them on the loan that they initially issued. In some cases, there could be very little left on the loan, and you could be in line for a significant bargain.

In the government’s case, whether you’re dealing with federal, state or local authorities, there is a different imperative involved. The government never issued a loan on the vehicles they auction, so getting their money back is not foremost in their minds. Most vehicles auctioned by governments have been seized, along with other possessions, from individuals who have been involved in illegal activity. As a result, since there is no target amount to derive from the auctions, vehicles can and do get sold for very little money.

You can get more information on this fascinating subject by getting my totally free report from the link in my resource box below. It takes you through the complete process of finding vehicles at auctions.

Governments also auction their own fleet vehicles that have outlived their usefulness. Usually those vehicles will be relatively high mileage, but don’t let that scare you off. Government vehicles are, for the most part, very well maintained, so the risk involved in buying a used car with high mileage is minimized.

There are some disadvantages to purchasing a vehicle at an auction. First, you don’t have a chance to test drive the vehicle. Second, you’ll usually have to pay cash on the spot, with no financing being offered. Third, no warranties are issued, so it pays to study the vehicles and to know your stuff. But as in anything else involving a purchase, if you prepare carefully and do your homework, as well as using common sense, you can find a great bargain.

If you adopt a careful approach and go in with our eyes wide open, you can win at the auto auction game. With the price of cars steadily rising, this may well be your best option for saving lots of money and getting a good vehicle as well.

Get my free report from the link in the resource box for more detailed information on auto auctions. Happy hunting.

About the author:

Jim Nettleton is a radio and TV professional with wide-ranging interests. Get his free report “Auto Auction Secrets Revealed” here: http://www.jaynetinc.com/AutoAuctionSecrets

Prepare Your Car for Winter: Four Things to Do Now

If you have never lived in a cold climate, you probably haven't had to deal with driving and handling a car in snowy conditions. There is a lot of preparation that needs to be done before you can drive safely through the winter. Just as you make sure you are prepared properly with winter clothing and gear, your car needs a winter wardrobe. Use the following steps to help ensure your car operates safely during the winter.

Preparing your car for winter breaks down into two categories: regular car maintenance and specialty items to deal with inclement weather. Regular car maintenance includes things that you do to your car year round. You need to make sure that these maintenance tasks get done before the weather starts to change so you can make sure that your car is running at its optimum level.

Before the winter starts, you should get your car's routine maintenance up to date. Getting your oil changed and your brakes fixed are essential in preparing your car for winter. Roads can be dangerous after the first snowfall. If you opt to go for snow tires, you should get them installed several weeks before winter hits. Snow tires aren't always necessary but they are a good idea if you are going to be driving in a place that experiences a lot of snowfall. Even if you don't need snow tires, check to make sure that your tires are in good enough shape to handle the wintry conditions.

Test out your windshield wipers before the first rain or snowfall. Be sure the wipers don't just smear water across your windshield. Windshield wipers that work improperly can severely reduce your visibility and put you at risk for getting into an accident. Replace your windshield wipers and take a look at the special winter windshield wipers that are available on the market today. If you live in an area where you frequently experience snowfall, this may be a good option. While you're at it, make sure that your windshield wiper fluid container is filled, and put an extra gallon on fluid in your trunk.

The next part of car preparation is gathering together the supplies that you'll need to get your car running when the weather is bad. These supplies should be kept in two spaces: your garage and in your car. For your garage, you'll need a shovel, a small broom and some de-icing spray. These are necessary in order to free your car from any heavy snowfall that occurred the night before. You may also find an ice scraper handy.

For your car, you should carry an additional ice scraper and some de-icing spray to use if you have to park outside during work hours. These items should be kept with a winter emergency kit that is stored in the trunk of your car. In addition to the scraper and spray, you should store a blanket, some dry snacks, first-aid supplies and bottled water. If you're ever stuck in a snowstorm, these items will help you survive. You can easily find emergency kits and necessary supplies at your local discount store or online. 

While driving during the wintertime certainly isn't something that you should worry about, you should take the steps necessary to prepare your car for the coming months. Get your car tuned up and stocked with emergency supplies and you'll be ready to take what ever the winter weather throws your way.

Stick Welding Tips and Basics

If you want to learn Welding it will take practice and a little patience to learn to do it in a way that will produce fine welds. This is an important thing to remember although some people may say they never had to practice much.

Welding is one of the basic methods of welding that many students learn as they are just beginning to learn welding. This is also a method of welding that is high in demand because people need this help whether they are working iron, pie, boilers or building ships.

You will find that you will need the skills of all types of positions including flat and horizontal and ventricle or overhead welding. All of these will take some time to learn and some will be more challenging than others.

Here are some tips to help you Stick Welding :

1. The right electrode for the job -- many people aren't sure of the size of the electrode they should use and this is important to know. The size of the electrode will depend on the situation you are welding within. In this situation you will be fighting against gravity if you are doing the weld vertically so you will want to use an electrode that is AWS classified as 7018 because they are low in their powder content.
2.Every welder needs a weld shelf especially if you don't want to loose any of your electrodes to gravity when you are doing horizontal or verticle welds. You can do this by creating a serious of little shelves so you can do a section at a time so that you can continue to work above a weld that you have already laid. This will create a situation where one puddle will freeze in time to hold the next weld.
3. Don't undercut if possible -- this can happen because you have to weave the electrode and sometimes your work may be gouged and not have enough fill metal. When this occurs, you will be working against gravity because it will work to pull your fill metal away from the space you are working. You can reduce your puddle size to help you have more control in this situation.
4.The industry has standardized on certain sizes of metal so its best to stick to these and not get off on odd sizes that aren't standard. These metals will be easier to find and you can weld them fester. Stick with the ones that are AISI-SAE 1015 to 1025 so that you can be sure that you have what you need.
5. Make sure you know your arc length -- a good rule of thumb is to use an arc length that is the same distance from the metal as your electrode's thickness. As an example, if you have an electrode that is ¼" thick, then have your arc ¼" thick. Also remember that as you use the electrode, you will have to move it closer to the metal.

These tips will help you develop a more even weld and keep things more controlled.

Welder World is a brand new community website for weldering to connect with one another and gather free information on welding. Come by WelderWorld to get your free Ebook on Welding Basics just for joining the Welding community for free. There will be many welding forums, welding blogs, and welding members to share information with as well as a free ebok just for joining that is all about Weldiing Basics. Come be A part of our Welding Community.

What Can You Do About The Gas Prices Increase ?

Rising gas prices is certainly a sensitive issue right now. And of course any discussion of gas prices prompts the question - will the price ever come down to a price that is reasonable or that was charged a few years ago ?Although you may see small reductions, the chances of going back to prices from a few years ago seems unlikely. With the potentially bleak economic outlook and an impending recession, high gas could will pose extra problems for workers who are unlikely to see an increase in pay in line with the inflation in the consumer price index. So what does the future hold for gas prices and how will people change their motoring habits.

Gas prices may go decrease in the immediate future. Fuel costs may actually go down in the interim if the need for gas decreases sufficiently. People will car pool or develop other strategies to reduce car travel, like working at home once or twice a week. Automobiles can and will become more efficient as research and development come up with better fuels. Therefore simple market forces like supply and demand will keep the price stable even though the long term trend will be inflationary.

However, one reason that gas prices will remain high is that oil refineries will continue to spend millions of dollars finding new ways to refine gasoline so that it burns more cleanly. The purpose of this is to adhere to stricter emissions standards as required by various agreements. They also have to develop employees and to undertake R & D for future advances.

So will the government act to regulate the gas price? Some nations have come up with plans to reduce the gas price but they are hard to implement and successfully administer as the govern derives plenty of revenue in taxes from gasoline usage. So while the prices of everything in the United States skyrockets due to the cost of fuel it is up to the people to make the difference to answer the question will gas prices ever go down.

People will travel less and spend less, hurting our economy even more, and as the cost of food rises, the quality of food people purchase will decrease which will probably result in higher health care and insurance costs. Basically, people have to plan their activity better, for example, try to do all your errands in one location at the same time so that you can save on fuel consumption and time.

The way to act is to voice your opinion. Don't mutter on to your neighbors or even your work colleagues, go to the people that can act for you - your elected officials. Write them, call them, email them, after all, your taxes pay their salary so they are on your payroll. Unfortunately big oil corporations can have some influence on elected leaders, but many voices raised as one can also hold a great deal of influence and help to initiate the changes needed.

So will gas prices get back to a price that is reasonable and affordable by average wage earners? Unfortunately, the things that determine the price of fuel are varied and often work at cros purposes, so the chances that they will all work together to bring about change in the gas price is unlikely. Even so, with your views added to the rising list of people who want change, our country’s administraters may take heed and implement a plan to halt to the out-of-control, inflationary spiral.

Even if the governments and oil companies appear indifferent to rising gas prices, ther is something you can do to make your car more fuel efficient gas to hydrogen conversion kits. Effectively they change the mixture of fuel that  your car uses by mixing it with hydrogen gas. This is thought to improve fuel economy. Ther are plenty of manuals around that give you step by step instructions on how to install such a system in your car. Learn more about the leading hydrogen conversion kit guides, including water car pro at water for gas reports

How to imcrease your fuel mpg with water

 

It seems highly unlikely that by simply fitting a water container in the engine compartment of your car, inserting some electrical plates and using the gas that is generated to add to the normal fuel in your engine, you can greatly improve your fuel MPG. But thousands claim to have done just that. Now, fortunately, there is a whole range of e-books on the subject, showing you exactly how to do it. E-books lke SimpleWaterFuel and Gas4Free tell you, step-by-step, how to construct and install a system and how to get the maximum fuel mpg out of it.

There is no doubt that the technology really works because a quick search will bring up hundreds of glowing testimonials. But if that's so, you'd think the automobile manufacturers would put it into all the cars they make, wouldn't you? Even if the hydrogen generator system has already been patented, a simple licencing arrangement could easily resolve that issue. After all, the environmental benefits and financial advantages that would, accrue would be huge. Why would any manufacturer not want to include this modern technology in their cars to improve their fuel mpg? Surely car sales would increase enormously if the car in question had twice the fuel mpg of any other car in its class. 

There must be something preventing the car companies from taking the plunge.

Are the oil companies trying to protect their interests and applying pressure somewhere? 

Are they in a cartel? Are national governments involved in this?Could OPEC be involved - one wonders what their stance might be on oil saving technology? It’s not at all clear is it?

A quick search of the web will reveal numerous testimonials from satisfied drivers who have fitted the systems and report remarkable results. 

Now I’m not stupid enough to believe everything posted on the Internet is true so I’m going to fit a system in my 2003 Toyota and see just what sort of fuel mpg savings I can make. 

Fortunately, although I’m not a mechanic by any means, I do enjoy doing DIY projects and from everything I’ve read so far all the systems look pretty simple to build and install. As this technology becomes more and more accepted, I'm sure you will be able to find mechanics offering custom-built systems all ready to put under your hood in just a few hours. There seem to be several main e-books available and I found this review which may help you to choose which one to go for.

 

Save Big With Used Cars

We all know that driving a car off the lot causes to drop in price by two thirds. Pretty much all people know this, but they still get new cars. Get this: depreciation of a new car actually costs you more than the gas ever will.

Let me tell you a story. I drive a 1990 Honda Accord with over 200,000 miles on it. It cost me $1700 six years ago when I bought it, and I've been driving it ever since. It fuel efficient, is big enough for most of my needs, and as been generally reliable all things considered.

Of course, I've had to put in a few repairs here and there. I've needed to swap out an alternator, replace some brake pads, and change some hoses that were leaking. Total, I've spent about eight hundred dollars on repair parts over the time I've owned the car.

My insurance is cheap. Since the car is so old, I don't need comprehensive and collision insurance, which save me a lot on my monthly premiums. On the whole, this car is amazingly cheap. Is it sexy? Heck no, but it does it job while letting me spend my money on more important things.

Let's think about what a new car would cost to get us the same point A to point B functionality. Say you spend $20,000 or so on a new Accord. Right off the bat, you're out more than 10 times the price of my old Honda. Add more to that if you didn't pay in cash, and took out a loan.

You're going to need insurance. Since you just bought a shiny new car, you'll need both comprehensive and collision insurance, which can be high, especially for younger drivers in newer cars.

This car will still need money for maintenance. All this time, the car will be loosing significant amounts of its value. Do you think this is a good way of spending your hard earned cash?

Buying used will allow you to save a lot of money on the expense of owning a car. Imagine how much more free your monthly budget would be in the absence of expensive car payments and high insurance premiums. Buying a cheap used car buys you financial freedom.

Finding A Classic Car Auction - Tips & Tricks

It's best to have some ideas on where exactly could a location for a classic car auction be, if you are already searching for a classic car. It is a fact that there are enthusiasts who are more attracted to buying old cars than new ones. Others even make it a hobby to go to such auctions. Likewise, some of them do have a wide collection of old-aged vehicles.

Now, you might wonder why many are awaiting classic car auction coming up notices in their areas. Well, the thing is that such popular and public auto auction is a great place to buy some rare vehicles, those tht were popular decades ago. Many different types of vehicle under various running conditions will be shown in this auction.

It is true that there arent so many vitnage vehicle auctions to be found, but there is always a way to find at least one. One of the good options you should try is a vintage vehicle magazine and start a search. Magazines are among the media used by auctioneers to announce upcoming classic car auctions. These kind of magazines are also collected by vintage vehicle aficionados, in most cases. An advice here is to go for popular magazines. This is because auctioneers are likely to advertise on magazines with wide readership.

Meanwhile, attending functions that have something to do with vintage automobiles is another way to learn dates for auctions. The world of vintage vehicle is small, thus information on classic car auction coming up schedules may be spread easily.

Of course, there is one great venue to get your hands on some fresh vehicle auctions, Internet. With people enjoying the convenience of the Internet nowadays, it is not surprising if information concerning vintage automobiles have also invaded the web. Search engines are your best friend here and you need to use them. It's an option that is great for all those busy people who are interested in these auctions, but simply do not have time to hunt one of them.

Improving your fuel mpg with hydrogen

A while back someone asked me to have a look at the latest ebooks that give instructions on how to improve your car's fuel mpg by augmenting the conventional fuel with hydrogen. This combination of hydrogen and oxygen is then fed into the inlet manifold of your engine and would, in some cases, double the fuel mpg of your car. This got me to wonder why all the hundreds of technical ideas that seem to offer real solutions to real problems have been completely ignored by the major car manufacturers. 

It seems that some had not been able to attract any funding to continue their research or they had been the subject of various sorts of threats.

It seems that some had been offered money to desist from their research and some had even died in ways that wre somewhat questionable.If these sorts of claims had been made by just a handful of people then it'd be easy to dismiss them out of hand. However, claims like this are popping up all the time. So what is going on?

Look at the average fuel mpg of the average car. It’s improved by about 20 – 40% in the last forty years. However, if you look at the cars that enter economy trials and competitons, you'll see that well over 100 mpg is achievable with little difficulty by ordinary cars. With all the technology now available to car manufacturers it’s difficult to believe they are unable to develop engines that are both economical and powerful. You'd have thought that they leap way ahead of their competition if they came out with a car like that.

I need to do a lot more digging to see what's going on here, but, before I do, I'm going to put a system in my 2001 Honda to see if it does what it's supposed to. Fortunately the parts and the instructions are very inexpensive. I’m pretty hopeful as the technology seems sound and the products do seem to have had a very good reception from everyone who has tried them. 

Of course, all fuel mpg economy systems have come under close scrutiny recently because, as the oil price has rocketed, improving fuel mpg has become a top priority for many drivers. There are numerous fuel saving offers out there and it pays to tread carefully and not rush in to anything. However, you probably want to get on with it and for me, the best option seems to be the hydrogen generating systems that I've been discussing.

Read my reviews here and see what you think

 

Police Auto Auctions Is The Place To Finding Good Deals]

government auctions

The majority of average citizens are not aware that most police agencies, including your local town's police department, your county Sheriff's department, as well as the law enforcement agencies at the state and federal levels, have massive amounts of property of all kinds in their possession. This property has either been seized or confiscated by the powers of the agency, or it was lost or abandoned by the former owners. When the warehouses and parking lots start to get filled up it is time for general police auctions and police auto auctions to take place.

While some of this property that goes into a police auto auction, or a general property auction, is there as the result of arrests, seizures and forfeitures, there is also a lot of property in the warehouses of public agencies simply because of the carelessness on the part of the property owners. There are many cases where someone absentmindedly leaves something like a bicycle behind and never takes the additional steps to see if it had been turned into the authorities. In addition, a great deal of personal property of all kinds is confiscated from theft rings and drug busts, and because the property was not marked with any identification, it was impossible for the items to be returned to the rightful owners.

At the general property government auctions you will find an incredible variety of clothes, electronics and household items, but it is the police auto auctions that people seem to get the most excited about because of the incredible deals on vehicles that are possible. Not only will you find cars, truck, SUVs, and vans at these public auto auctions, but often there are recreational vehicles and other "toys," such as boats, motorcycles, bikes and jet skis.

A police auto auction can be a very practical place to search for a reliable car that is in good condition, especially if you would like to make it yours for just a fraction of the real market value. Many of the seized cars at these police public auctions tend to be a mixture of vehicles that are later models, as well as many that are 5 to 15 years old. Most of the cars were impounded because the owner of the vehicle committed some type of crime that gave the law enforcement agency the right to seize the vehicle and sell it.

Because most of the seized cars that have been impounded by police were operational at the time that they were taken off of the street because of driver infractions, many people feel more secure about buying from a police auto auction. In contrast, there are many repossessed cars that are sold through auto actions by banks and finance companies because people stopped making payments on the car due to some kind of mechanical malfunction.

Those who want to go and check out the police auto auctions in their area can call or visit the local law enforcement agencies that are nearby and convenient, and ask them for a list of the various auctions that will be coming up. It is a very good idea to go to at least one auction to observe the procedures before you go with the intention of placing a bid.

Less Expensive Car Insurance

Cheap auto insurance is an important step towards risk free driving. free on line car insurance quote Always check around and do your research before purchasing.
It is a good idea for an insurance customer to be selective in choosing an insurer. Those who are looking to purchase car insurance want both great service and inexpensive rates from their potential insurance company.

Mentioned below are some tips to help in finding the cheapest and best auto quotes:

Understand your requirements under the laws of your state concerning auto insurance coverage: Some states require a person to have minimum liability coverage. when the policyholder is affected due to accident this coverage includes damages. There are plenty of states having no-fault systems of auto insurance. In few states it is not mandatory to provide insurance coverage. Medical costs are also non obligatory in these states. Even coverage for car damage can be optional in some states.

A proper profile for personal auto insurance will  require a write up which will cover: The information as to where you drive,if there is anyone else driving the car,type of vehicle being driven,residing place,driving record and the optional safety features put in the car. The profile allows for quotes and comparisons to be an easier process.

It is imperative that prior to signing or making a payment for anything, you pore over the fine print and clarify any critical questions you may have.

Make sure to have your policy with you at all times. Give a call to the insurer to keep the policy up-to-date. Inform the agent of any changes and periodically ask them about any discounts.

Additionally, it is crucial to schedule a yearly evaluation of the plan with the insurance provider. Periodically one must search for cheap auto insurance quotes through online.  It is essentially for getting good quotes. They are available in both an easy and quick manner. (Get one now--just scroll down to the links below)

Store auto insurance information in  the car. Most states require a card proving that the vehicle is insured to be with the driver while driving. Even though it is not required, it is a good option to carry them so that, they have the insurance information in case of an accident.

There are various ways to tailor the cheap auto policy coverage based on the specific needs. The people may select their individual policy coverage and amount for their wish even the state is in the minimum policy coverage requirement level As well as having sufficient coverage choices, there are in addition general plan choices.

Choosing the plan time-frame: The insurance coverage is effective for the time period laid out in the plan. The time is determined when the policyholder enters into a contract with the insurer. auto insurance myths.

Typically, vehicle plans are in effect for either a year or six months at a time. Accordingly, an individual can also purchase auto insurance for shorter or longer periods. As a general rule, premiums should be just a bit lower when buying policies for a longer time frame. Longer term policies give more assurance so they will pass the savings on to the consumer.

If you are an insurance policyholder, please be aware that you can cancel your policy at any time before its term expires. However, they have to remain aware of the fact that, most insurers have certain procedures that they need to follow in order to do so. More instant auto insurance quotes.

What Are The Grey Areas On Warranty Plans

warranty plans

It seems hard to believe that businesses can remain open but wrangle honest customers out of money needlessly. Yet that's the case at car dealerships across the nation every day. Technically, the salesmen aren't breaking any laws. But could they give you a better deal on warranty plans? Probably. The way the system is designed (to give added commissions for extended warranty plans sold) may lead some salespeople to pressure you into choosing a warranty immediately at the time of purchase. People who choose not to make hasty decisions often turn to the internet to secure a better deal by cutting out the middle man and purchasing an automobile warranty directly from the source.

One common problem people run into is to fail to read and understand the agreement before they get work done. Knowing the right questions to ask your warranty company is crucial, experts say. For instance, ask if you can get the work done at any shop, or do you have to look for a certain certification, or in some cases return to the dealer? Additionally, is your car covered for "wear and tear" damage or just mechanical failure?

You should have a comprehensive list of all the parts that are/aren't covered! Sometimes you'll get a "bumper to bumper" warranty that covers everything except for the wear items, like brakes and tires, while other times you'll get a "power train" warranty, which covers the engine and transmission. While it's rare to find a company that offers coverage for everything, you should ensure that some of the most expensive repairs will be taken care of.

Secondly, you should find out if there are certain stipulations that would make you ineligible for utilizing purchased warranty plans. In some cases, consumers have had their claims denied because they continued driving after their engines overheated or they attached unauthorized tow hitches to their cars. Sometimes, if you don't get regular oil changes or fluid top-ups, then you could be at risk for vetoing your right to coverage as well. Know the rules and stick to them!

Warranty plans can be intimidating at first, especially because there are so many companies to choose from. You may want to try AutoWarrantyReviews.org or another comparison site. Look at how long the warranty company has been in business and how many claims they've addressed, their BBB rating, if they have clients like car dealerships and banks, if they fully explain their plans with details, if they offer written terms and conditions, if they cover all 50 states (in case you're traveling and have a problem) and if there is some sort of money back guarantee.

The Top Approach To Save On Auto Insurance

If you search online for advice on how to reduce your car insurance cost, you will find thousands, maybe millions of sites and articles that in theory give you the answer you are looking for. free car insurance quote online On the whole, these articles are very useful although they usually contain very similar advice. Nevertheless, they pay very limited attention on the out-and-out best way to save wealth on your car insurance.

Getting the cheapest automobile insurance rate is really quite simple. The only thing required is excellent driving skills. The best thing about this site as compared to other sites is that there would not be any more additional cost for you even for tricks about the make of your car, gender, age or otherwise.

Actually, having a good driving record leads to smaller premiums, more so than any other way to reduce your costs. lower auto insurance rates Not getting into accidents is one of many parts of being a good driver. All traffic laws must be followed by everyone, including you.

For example, if you constantly drive over the speed limit eventually you will probably get caught. If you are looking for lower automobile insurance costs, speeding tickets are only going to hurt you. Parking tickets, however, do not count against you. If they're that expensive, you shouldn't be craving to purchase them.

You should try to avoid moving violations, they will count against you. This means paying more attention to road and speed limit signs and always making sure you indicate what you are going to do.

It would be advisable to take a driving course to improve your driving skills. Some insurance companies will even lower your insurance after you take one, although the discount is usually much larger for younger rather than older drivers. Although, you might want to take it just to improve your driving skills.

Driving records are important for older drivers. Insurance companies tend to charge higher rates for younger drivers until they figure out if they are likely to engage in risky behaviors. Therefore, rates usually lower when a driver nears the age of twenty-five if he has had a decent driving history.

What age is good for driving? Moreover, if you do have violations on your record they will be discounted to certain extent by time. For example, a speeding ticket you got 20 years ago won't hurt you as much as one you got last year. Therefore, customers that don't have a great history of driving can still receive incentives for improvement.

So to recap the absolute best way to save money on your car insurance is to be a good driver. This means staying out of accidents (at least ones that are your fault) Traffic laws should be obeyed. If you do these two things I guarantee that over time you will pay less for your car insurance than you would otherwise. If you pay for car insurance that does not man that you pay more for car insurance. fast free auto insurance quotes.

How To Increase The Gas Mileage When You Drive

One way to save gas is to look for a job that won't be far from your residence. The fact that one would have to drive lots of miles to go to work can put a big hole in one's pockets, especially if one must use the car.

One of the myths that surround saving gas is that topping your tank up to its brim makes you have more gas to use throughout the week. When you top up your gas tank and you fill it up to the brim, you risk losing most of it through over-spilling. The loss of gas from your gas tank can be avoided if you don't always fill your tank to the brim.

You can use more than one gas credit card if you want to. Once you expend the rebate rate of a gas credit card, you can apply for another gas credit card to enjoy its rebate rate. With more than one gas credit card, you can save tremendous costs on gas.

Lots of individuals mention that green vehicles are becoming very accepted for to save gasoline these days. Although I haven't used a green car before but they say a green car is one that does not rely on gas to power it. Wheter or not this type of vehicles exist is something that deserve some analyzing. But the way the cost of gas is going, green cars will surely be an option for many if such cars actually exist and work as advertised.

You can walk instead of using your car all the time in order to save gas. As an alternative to using your car, walking comes with tremendous health benefits such as the loss of extra fat, leaner muscles and a healthier heart. Walking to closeer destinations instead of driving can keep the gas in your car much longer.

Slamming on the car breaks unnecessarily tends to cause loss of gas. It's really true that aggressive driving is responsible for gas loss in many cars. Jack rabbiting is a driving habit that can cause you to lose more gas than you should. Take the time to learn how to avoid these habits and you will save a lot of gas at the end of the day.

A vehicle in general works better and save more gasoline when is kept in great conditions. If you fail to maintain your car, you will work with a car that uses up more gas. Keeping your car in a good regimen of maintenance is vital for saving gas.

Getting an online job may just be the right answer to the question 'how can I save gas'. If you work at home on the Internet, then you don't need to commute to and fro your place of work. This is indeed a great way to save on gas and still live your life, especially one that still puts food in your mouth and feed your family each month.

Machining Fundamentals

cnc programming

Tooling Offset
I thought this would be a great place to do a quick talk on Tooling Offset.  Tool Offset is the amount you must “Offset” the tool while machining.  For example, the tool paths that we created in CAM Software are located in the dead center of the tool unless you do something about it.  Most times you set the tool offset in your CAM program, but sometimes you might have to do it during the machining phase, depending on your machine.

What if you had a one-inch diameter tool, we will use an end mill in this example, and you needed to take off .25” around the perimeter of a 5” by 5” block of aluminum?  Without tool offset, the tool path would be around the perimeter of the block.  The end mill would take off half of its diameter or .5” inches.  You need to offset the tool so this does not happen.  In this case you would offset the tool outside of the block by .25”, then the end mill would take off .25” of material.

Zeroing the machine out
When beginning your machining, you always need to zero out the machine.You need to let the cnc control software know where the starting point for the project is.When zeroing out a machine, you will use an edge finder.  Most times in CNC Machining, you will just pick your starting point on the steel and begin the program there.

The final “Part”
Parts are the outcome of your work.  That is unless you are making artistic pieces.Parts are built to a spec.Machinists will check the parts they are making as they come from the CNC Machine.  Many times, they will use a go/no-go gauge.  With a go/no-go gauge they can quickly check out the critical dimension of the part and reload the machine.

Chips?
Machinist call the material being removed “Chips.”  This is because most things that are machined are metal and they come off the part in chip form.Chips can be dangerous and sharp.You have to be aware that chips will be flying around as they are cut away.  Quite a few machines will have enclosures around them to block these chips from flying around.

CNC Information Free Community Site:
If you want to know more about Computer Numberical Control, go over to http://www.cncinformation.com
You can join for Free and you get two free CNC ebooks. One is a G-Code Guide and the other one is a CNC eBook. You also get access to the Free Video Series...Image to CNC Art when you join the community.

Car Insurance Deals

The most useful characteristics of auto insurance companies are that they offer the best deals for their insurance, the best range of coverage options and also the best priced premiums. on line car insurance quote State regulations mandate that in order to drive an vehicle you need to have a minimum amount of insurance coverage. Therefore it is seen that the plans are equally in demand as the cars themselves.

Due to the increase in demand a lot of auto insurers have appeared and this helps people to choose from a wider range. Hence, it is wise to choose a policy provider carefully, and only after doing thorough research, since the yearly premium can be a rather large sum.

If people meet certain prerequisites, they have the chance to get the best deals from top auto coverage companies. For several reasons, many auto insurers' policies provide discounted rates for their different services. These include having an anti theft device, driving multiple vehicles, learning defensive driving, getting new vehicle protection, owning your own business, being a good student and of course remaining accident free.

Apart from the discount offered by these auto insurance companies, it is better to ensure the financial stability and longevity of the chosen firm. NO Quick and Free Van Insurance Quote Online.

Similarly, you have to choose your insurance policy wisely. You may find yourself with future difficulties if you don't choose an insurance policy wisely.

For instance, if you pick only third party insurance and then suddenly you are injured due to an accident, where damage has occurred to car. Here, individuals won't receive reimbursement from the insurance company and will have to pay the costs themselves.

Even though it may cost more full insurance coverage is the best choice. You will have a peace of mind, since your insurer covers all the damage costs.

After reviewing all the policies and rate plans; weigh the pros and cons of each before choosing.

Discussed below are some of the guidelines to choosing from among the cheapest auto insurance policies:

To obtain the excellent auto deals, you have to shop around. People can find out which companies provide the highest levels of insurance coverage for the lowest premium prices by shopping around.

As you negotiate with a car insurance firm, inquire whether they provide any type of discounts. It might be possible for individuals to gain benefits from such discounts. There are several discount offers for good students, accident free drivers and for fixing security systems or air bags in the vehicle.  

It is easy to obtain a lot of quotes online when looking for auto insurance, as opposed to searching for good deals from local companies. Because scams abound on the internet, disreputable auto insurance companies such as these should be avoided.

Auto insurance is something you need to comparison shop for, look around for the best prices. Start by getting free quotes from numerous different companies and you are well on your way to saving. vehicle insurance quote on line.